Excavating Equipment
Cat Pumps Spline Shaft Pumps
Cat Pumps offers the trusted performance of the 2565 and 3560 plunger pumps with a direct-mount flange and hollow spline shaft design. This compact solution provides significant space saving for mobile hydroexcavating applications where every inch matters. The 2565T13 mates with SAE B hydraulic motors using a 13-tooth spline shaft, delivers up to 20 gpm at 3,000 psi and is over 7 1/2 inches shorter than the standard bell housing configuration. The 3560T14 and 3560RST14 pair with SAE C hydraulic motors using a 14-tooth spline shaft, producing 20 gpm at 4,000 psi or 25 gpm at 3,000 psi. Both models reduce overall width by more than 8 inches, permit motor mounting on either side and can be equipped with an optional electronic RPM speed sensor to ensure accurate, consistent operation in demanding applications. 763-780-5440; www.catpumps.com
JETTERS NORTHWEST HOT-BOX
Frozen pipes and frozen ground can slow down sewer/drain jetting and hydroexcavation work, but tankless HOT-BOX heater units from JETTERS NORTHWEST can add hot-water capability to a cold-water sewer jetter or hydroexcavator to speed up the job. It can easily quick-connect inline to heat the cold water from your machine’s pump to send hot water to your nozzle for faster jetting or hydroexcavation work. Totally portable, it is easily transferred from vehicle to vehicle and job to job. Heaters run on diesel (or any home-heating oil) and the unit draws only 6 amps of 115-volt power, making it a light load for a generator or 115-volt circuit. Two models are available ranging from 350,000 to 480,000 Btu. Units can be upgraded into a line-curing heater for relining work. 877-901-1936; www.jettersnorthwest.com
Pipe
Asahi/America Poly-Flo
Asahi/America’s Poly-Flo is a co-extruded double containment piping solution engineered for safety, durability and ease of installation. Available in both Advanced PE and PP-R, it’s designed for both drainage systems and pressurized chemical transfer applications. It provides reliable protection against leaks and environmental contamination. Available in 1-by-1.5, 2-by-3, 4-by-6, and 6-by-9-inch sizes, the system is ideal for facilities with tight space constraints such as water and wastewater treatment plants, and for outdoor installations exposed to varying environmental conditions. Its co-extruded design ensures a consistent, tight bond between the carrier and containment pipes, reducing installation time and cost. It offers exceptional resistance to corrosion and chemical attack, making it a trusted choice for applications involving multiple or aggressive chemicals. With its simplified joining process and robust design, it delivers long-term performance, safety and reliability in demanding fluid handling environments. 800-343-3618; www.asahi-america.com
Pipe Parts/Fittings
ACME Trenchless Pipe Winch
The ACME Trenchless Pipe Winch makes trenchless pipe pulling quick and routinely easy. It delivers the pulling power needed — 20,000 pounds breakout force — applied to MAX 7/16 pulling cables which have a minimum rated breakpoint of 24,000 pounds. The pulling cables are reusable, and tensioned pulling cable remains inside the confines of the winch frame. It attaches to a compact excavator or backhoe via a quick coupler and will dispatch to the access pit at any approach angle, allowing for the preservation of the original bury depth of the existing waterline. It works with lead, galvanized, copper and plastic piping. 920-376-4222; www.acmetrenchless.com
RELINER/Duran Inside Drop Bowls
Inside Drop Bowls and stainless steel pipe support brackets from RELINER/Duran simply bolt to the manhole wall and can be cleaned and inspected from above. The compact, low-profile bowls are available in dozens of sizes to fit any application.They can be used for service lateral, mainline sewer and wet well drops. The adjustable clamping pipe brackets are easily installed and available in noncorrosive 11-gauge 304 or 316 stainless steel, and they are AIS Certifiable. They securely attach pipes to structure walls with no protruding hardware and are fully adjustable to fit irregular surfaces. Clamps are stocked for 1.5- to 30-inch SDR35, Sch 40, HDPE, C900 and DN pipe. Modular Manhole Invert Channels improve manhole hydraulics, reducing maintenance, turbulence and odor. 800-508-6001; www.reliner.com
Pipe Cutter
NuFlow Technologies Trelleborg PowerCutter 200 E
The Trelleborg PowerCutter 200 E, distributed by NuFlow Technologies, delivers powerful, precise and quiet pipe rehabilitation performance with an electric-driven milling motor. Designed for 8- to 24-inch pipelines, this advanced cutter combines strength and efficiency in a compact and quiet package. Its four-directional maneuverability and dual-camera system provide exceptional visibility and control for accurate cutting and reinstatement. It offers electric-powered performance, so there’s no need for generators or compressors. It has ultraquiet operation, reducing noise by more than 70 dB, enabling 24-hour work with minimal disruption. Intelligent electronics prevent thermal damage and extend equipment life. Its lateral location software enhances accuracy and efficiency during cutting and reinstatement. Its hybrid cable design includes an integrated water hose for camera cleaning and compatibility with third-party CCTV systems. 866-430-2134; www.nuflow.com
Pipe Lining
BRAWO SYSTEMS Remote LC
Remote LC from BRAWO SYSTEMS has a modular design and is largely based on the BRAWO Drum 4.0 with side lock for the light curing unit and the BRAWO Magnavity SX light curing unit. The central deflection elbow enables the liner to be inverted into the connecting pipe. With BRAWO Remote LC, connection pipes DN 100 to DN 150 with bends of up to 90 degrees can be rehabilitated from main sewers of sizes DN 200 to DN 300 with rehabilitation lengths of up to 164 feet. 240-796-5007; www.brawosystems-usa.com
CUES LOCK
CUES LOCK is a no-dig structural point repair solution. Cross-bore strikes, cracks and separated joints, just to name a few, can be repaired in as little as 30 minutes, with no digging. The gear required to install is very minimal and, on average, will pay for itself in the first one to three repairs. This saves significant time and money versus dig and replace or traditional lining while improving safety for install crews by limiting exposure. The sleeve is constructed with a 316 stainless steel core, rated to a 100-year service life. It is available for pipe from 6 to more than 108 inches in diameter and in 12- to 36-inch lengths. Sleeves can be installed in series to repair longer defects. It can be used with an existing CCTV system. 800-327-7791; www.cuesinc.com
Emagineered Solutions THE SHOOTER
THE SHOOTER 12 from Emagineered Solutions is a continuous air-inverter for CIPP. Simple to operate and built to last, it has a range of 4 to 12 inches and up to 15 inches with the conversion kit, a knife gate for after the liner tail passes and comes with either a self-lubricating hand truck or the basic non-oiler cart. THE SHOOTER 24 for 15 to 24 inches is trailer-mounted and comes with a knife gate and remote operating station on the fender. An optional conversion kit expands its range from 6 to 24 inches. Additional equipment offered include full steam packages with portable dry steam generators, steam hose, A and B Stations, water cure flanges and LED UV Y adapters. 541-504-0416; www.theshootercipp.com
Pipeline Renewal Technologies SpeedyLight+
SpeedyLight+ from Pipeline Renewal Technologies delivers LED-based UV light-curing technology for trenchless pipe rehab. UV CIPP offers clear advantages over other relining methods by being faster and producing stronger liners. It’s also less disruptive to communities and businesses — closures are minimal, and work can be completed without having to relocate occupants. LED UV cure eliminates safety risks such as the wrong mixing of resins or dealing with boiler systems. There are no working time considerations as you turn the light on and off anytime you want to stop or start the cure. Interchangeable cure heads show operators what’s happening underground, giving them the ability to control the speed and accuracy of the cure. It cures felt or GFRP liner and can cure 90-degree bends in lines down to 2 inches, as well as transitions and verticals. 866-936-8476; www.pipelinert.com
PPG Protective & Marine Coatings RAVEN 405
RAVEN 405 from PPG Protective & Marine Coatings is an epoxy coating designed to rehabilitate and protect concrete and steel structures exposed to the most severe wastewater conditions. It provides corrosion resistance in sanitary sewer systems and ensures long-term durability, helping extend the service life of aging infrastructure. Featuring high-build capabilities and chemical resistance, it can be applied to structures such as manholes, wet wells, lift stations and pipe linings, preventing further degradation from hydrogen sulfide gases and other corrosive agents. 888-977-4762; www.ppgpmc.com
Sauereisen F-88 Manhole Chimneyseal
Sauereisen F-88 Manhole Chimneyseal is a chemically resistant, elastomeric lining engineered to prevent I&I into the chimney section of manholes. This critical area of the structure experiences the greatest movement and exposure to chemical attack from acids, alkalis and salts. It forms a durable, flexible membrane that withstands horizontal and vertical movement caused by freeze/thaw cycles or ground shifts while maintaining a watertight seal. Offering reliable protection against water infiltration, extending the life of manhole structures and reducing costly maintenance in wastewater collection systems. It has outstanding chemical resistance to acids and alkalis, and remains flexible from minus 30 to 250 degrees F. It is easy to apply with a gloved hand, making it an ideal municipal maintenance personnel DIY solution. It is suitable for application on steel, brick or concrete substrates. 412-963-0303; www.sauereisen.com
Pumps
Gorman-Rupp 6400 Series
Gorman-Rupp’s 6400 Series line of end suction centrifugal vortex pumps is based on the Super T Series product line. An alternative for flooded suction applications, these pumps feature the same footprint and shaft height as comparable Super T Series models. They are available in 4- and 6-inch sizes, and can be equipped with straight- or winged-vane impellers depending on the liquid being pumped. The straight-vane impeller (VA) is designed for more aggressive, abrasive applications. This model is also better at handling stringy, fibrous debris. The winged-vane impeller (VB) is better suited for higher discharge pressures and incorporates a steeper performance curve, which requires less horsepower. Both impellers come standard in austempered ductile iron for handling tough abrasives. 419-755-1011; www.grpumps.com
Pulsafeeder NextStep
NextStep dosing pumps from Pulsafeeder are designed for high-resolution metering control and reliability and cover a wide range of applications including polymer feed applications. When “once through” or nearly constant chemical discharge and even distribution of flow is beneficial, the stepper motor pump provides high dosing accuracy, digitally controlled, high turndown ratio of 3,333 to 1, reducing pulsation and increased reliability of metering off-gassing and high-viscosity chemicals. Modbus or RS-485 communication keeps the process running smoothly even from a remote location. It comes with all valves, tubing and cables needed, including a foot valve with integrated low tank level alarm. 800-333-6677; www.pulsafeeder.com
SEEPEX BNM
BNM range pumps from SEEPEX are designed for large-scale applications where ease of maintenance is critical. These block pumps feature a rotating unit that allows the rotor and stator to be replaced without dismantling the rotor-sided joint, minimizing downtime. The sliding casing element provides direct access to the rotor connection and joint, enabling maintain-in-place servicing. This design eliminates the need to remove pipework or disconnect suction and pressure branches, streamlining maintenance procedures. It complements existing technologies like Smart Conveying Technology, particularly in scenarios where SCT’s design limitations arise. With separate disconnection points, users can access and replace key wear components — rotor, stator and mechanical seal — efficiently. This results in reduced maintenance costs, supports proactive servicing and enhances overall system uptime. The range is especially beneficial in operations requiring frequent maintenance or where accessibility to internal components is typically challenging. 937-864-7150; www.seepex.com
Pump Parts/Components
Smith & Loveless DURO-LAST SST Baseplate Conversions
DURO-LAST SST Baseplate Conversions extend the life of Smith & Loveless aboveground pump stations. A durable and cost-effective upgrade solution, they are designed to maximize system longevity and value by reusing existing rotating assemblies and controls, significantly reducing overall upgrade costs. The conversion is available for all Smith & Loveless aboveground wet well mounted pump station models. Each conversion package is engineered to include the stainless steel baseplate, volutes, station piping, fiberglass hood with lift assist, wet well access entrance, control panel mounting struts with vacuum pump shelf, blower and vents, and all required hardware. It is designed to extend pump station life by more than 25 years while offering improved maintenance, operator safety and life cycle costs. 800-898-9122; www.smithandloveless.com
Valve
Singer Booster Pump Control Valve
The Singer Booster Pump Control Valve is installed inline directly downstream of the pump discharge and is available in a single- or double-chamber design. The single-chamber design facilitates supplemental modulating functions, such as pressure sustaining, pressure reducing and rate-of-flow control. The valve substantially reduces pump starting and stopping surges and has separate opening and closing speed controls. The double-chamber design has a built-in mechanical drop check that closes immediately in the event of a power failure when the flow stops, independently of the valve position. Surges are minimized by closing the valve before reverse flow occurs. It is suitable for most pumping applications, including suction lift and low differential head. 800-423-1323; www.muellerwaterproducts.com
Valve Boxes/Building Components
Legacy Building Solutions Tension Fabric Buildings
Combining rigid-frame engineering with the proven benefits of tension fabric membranes, Legacy Building Solutions offers fabric structures that are fully customizable. They utilize a durable rigid frame in place of the hollow-tube, open web truss “hoop” framing traditionally used for fabric structures. The strength of the structural steel frame provides several engineering advantages, most notably the ability to easily customize buildings to the exact width, length and height required. In addition to long clear spans, the buildings have straight sidewalls that maximize the usable square footage inside the structure. The design allows for much more structural flexibility than traditional fabric structures, including the ability to add lean-tos, mezzanines, sidewall doors and more. The structures are also engineered to provide desired overhangs or handle additional loads for items such as sprinklers and conveyors. 877-259-1528; www.legacybuildingsolutions.com
Orenco Composites DuraFiber
When planning project infrastructure, don’t forget to include housing for controls and other essential components. Orenco Composites DuraFiber prefab, easy-to-spec, easy-to-install buildings will meet your specs while providing lasting durability. The fiberglass buildings are designed for strength and convenience. Made with high-quality, fiber-reinforced polymer for corrosion, UV and impact resistance, the buildings are molded with integral walls and roofs for a single-piece, leak-free shelter. They range in size up to 50 feet long, 40 feet wide and 11 feet high. They can withstand 160 mph winds and support a 100 pounds per square foot live load. 800-348-9843; www.orencocomposites.com
Vivax-Metrotech ferrous metal detector
In today’s ever-changing landscape, vital underground assets often become hidden or buried under new surfaces, making them difficult and time-consuming to locate. Valve and maintenance hole covers can disappear after resurfacing, construction work or heavy snowfall. Vivax-Metrotech ferrous metal detectors enable the fast and efficient location of these buried assets. Most valve covers, maintenance holes and boundary markers are made from magnetic or ferrous materials – and these detectors are designed to find exactly those. Unlike general-purpose metal detectors, these specifically ignore non-ferrous materials, such as aluminum cans and bottle caps. They feature intuitive audio and visual interfaces, minimizing training time and enabling operators to work confidently from the outset. 800-446-3392; www.vivax-metrotech.com
